Category: QMobile Firmware

QMobile Z8 Flashing Solution

QMobile Z8 Flashing Solution: Yes i am going to write about QMobile Z8, Z8 Plus, Z9. These QMobile models are based on Qualcomm based CPU. In most cases i have seen Qmobile Z8 with IMEI null, No WiFi, And in most cases We are facing firmware flashing problem. Some basic problem in QMobile Qualcomm based phones.

Most searched Topics on Internet About QMobile Qualcomm Based Phones:

  • qmobile z8 imei null solution
  • qmobile z8 imei repair tool
  • qmobile z8 imei repair cm2
  • qmobile z8 wifi not working
  • qmobile z8 sahara failed
  • qmobile z8 imei repair

Reason QMobile Z8 Can’t be flashed?

In most cases i have noticed that, if your QMobile Z8, Z8 Plus, Z9 stuck on startup screen, Then there is huge chance of EMMC damaged. What is EMMC? EMMC is a short of Embedded Multimedia Card. EMMC are being damaged due poor quality. But in this post i am going to write about if your cellphone have good hardware (not damaged internally) then there are so many chances to unbrick you QMobile Z8.

How to Unbrick QMobile Qualcomm Based Phones?

In this case i have used Infinity CM2 dongle, But don’t worry you can try also even you have not any professional tool for Chinese phones. The most common problem in this case is EDL Mode. What is EDL Mode? EDL is short of “Emergency Download Mode” Most of user are getting failed message during using QPST or any professional Chinese service tools like Infinity CM2, Miracle Box etc,

How to Enter EDL Mode Qualcomm Phones?

To force Qualcomm phone for getting EDL Mode, We have so many methods. i will describe them below.

  1. By Volume Key: Press and hold [Volume Up + Volume Down] and connect USB Cable.
  2. By Fastboot: Execute command “fastboot reboot-edl” Read more about adb and fastboot
  3. By Test Point Read more about test point in this post [How To Unbrick Hard Bricked LG G3]

Most common problem in QMobile Z Series flashing failed, is EDL Mode some people don’t know about this we need to force this phone to get edl mode via volume keys. People pressing vol+ and vol- one or two times and leaving phone by saying not connecting.

In my experience i have noticed We need press and hold volume keys and power key until phone show us Qualcomm hs-usb qdloader 9008 mode or qhsusb_bulk in  device manager but in some cases we need to disconnect battery to flash Qualcomm phones.

My Last Day Experience With QMobile Z8

I received QMobile z8 with imei null and no service, Because of my already experience with this phone i decided to flash QMobile z8 with official firmware. I get rid on imei null every time by flashing official firmware on this phone. So started flashing with Infinity CM2 Qualcomm module. I get loader error and PC Stuck. So i tried again and failed again and again. The i decided to open phone to disconnect battery. So i opened and connected battery after disconnecting. but it was same so i flashed phone without battery and that works for me.

How to Flash QMobile Z8?

  • You must have a windows computer and a micro usb cable.
  • Download and extract QMobile Z8 Firmware on your PC and unzip it with any unzip utility download link can be found below.
  • Download and install Qualcomm Usb Drivers.
  • Download Qualcomm Flasher QPST_2.7.422.7z
  • Open QPST installation folder C:\Program Files\Qualcomm\QPST\bin
  • In bin folder you will find QFIL.exe open it and continue.
  • Make sure you installed Qualcomm drivers correctly.
  • Connect phone by pressing Vol+ and Vol- key to PC via micro usb cable.
  • You will see Qualcomm HS-USB QDloader 9008 port in you PC device manager.
  • Select Qualcomm port if QFIL not pick automatically.
  • Press “Browse” button and select prog_emmc_firehose_8916.mbn in QMobile Z8 Firmware folder.
  • Then Press “Load XML ” and select rawprogram_unsparse.xml if you want to install clean software on your cellphone. if you want to upgrade only then you should select rawprogram_unsparse_upgrade.xml file. but we recommend that you should install clean software because sometime upgrade make problems.
  • After selecting rawprogram_unsparse.xml you will be asked to select patch0.xml please select and continue.
  •  Connect Qualcomm Phone to your PC via USB cable by holding Vol- and Vol+ keys and select Qualcomm port in port selection.
  • Press “Download” button and let it complete phone restart automatically after download complete.

Download QMobile Z8 Firmware + QPST + Drivers.

QMobile Z8 Flashing Log:

Operation : Flash [ v1.12 ]
ForceFlashing : Disabled

Verify FW package ... 
Verification passed!

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ... 
Handshake passed!
BB_IDC_CPU : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 0C1139CD
ID_BLOCK_I : 007050E1
ID_BLOCK_L : DA2A40BE1985B2BD6ADF311ED9A03018
ID_BLOCK_L : C8BB05A4A938A223A6117AB3B17C6A51
Pickup loader from firmware package
Loader Sent! Initializing ... 
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000003AB800000 [ eMMC 16 GiB ] 
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Flash Chain : 175
Flashing now

Flashing : NON-HLOS.bin
Flashing : sbl1.mbn
Flashing : sbl1.mbn
Flashing : emmc_appsboot.mbn
Flashing : emmc_appsboot.mbn
Flashing : rpm.mbn
Flashing : rpm.mbn
Flashing : tz.mbn
Flashing : tz.mbn
Flashing : hyp.mbn
Flashing : hyp.mbn
Flashing : misc.img
Flashing : splash.img
Flashing : chglogo.img
Flashing : sec.dat
Flashing : boot.img
Flashing : system_1.img
Flashing : system_2.img
Flashing : system_3.img
Flashing : system_4.img
Flashing : system_5.img
Flashing : system_6.img
Flashing : system_7.img
Flashing : system_8.img
Flashing : system_9.img
Flashing : system_10.img
Flashing : system_11.img
Flashing : system_12.img
Flashing : system_13.img
Flashing : system_14.img
Flashing : system_15.img
Flashing : system_16.img
Flashing : system_17.img
Flashing : system_18.img
Flashing : system_19.img
Flashing : system_20.img
Flashing : system_21.img
Flashing : system_22.img
Flashing : system_23.img
Flashing : system_24.img
Flashing : system_25.img
Flashing : system_26.img
Flashing : system_27.img
Flashing : system_28.img
Flashing : system_29.img
Flashing : system_30.img
Flashing : system_31.img
Flashing : system_32.img
Flashing : system_33.img
Flashing : persist_1.img
Flashing : cache_1.img
Flashing : cache_2.img
Flashing : cache_3.img
Flashing : cache_4.img
Flashing : cache_5.img
Flashing : recovery.img
Flashing : userdata_1.img
Flashing : userdata_2.img
Flashing : userdata_3.img
Flashing : userdata_4.img
Flashing : userdata_5.img
Flashing : userdata_6.img
Flashing : userdata_7.img
Flashing : userdata_8.img
Flashing : userdata_9.img
Flashing : userdata_10.img
Flashing : userdata_11.img
Flashing : userdata_12.img
Flashing : userdata_13.img
Flashing : userdata_14.img
Flashing : userdata_15.img
Flashing : userdata_16.img
Flashing : userdata_17.img
Flashing : userdata_18.img
Flashing : userdata_19.img
Flashing : userdata_20.img
Flashing : userdata_21.img
Flashing : userdata_22.img
Flashing : userdata_23.img
Flashing : userdata_24.img
Flashing : userdata_25.img
Flashing : userdata_26.img
Flashing : userdata_27.img
Flashing : userdata_28.img
Flashing : userdata_29.img
Flashing : userdata_30.img
Flashing : userdata_31.img
Flashing : userdata_32.img
Flashing : userdata_33.img
Flashing : userdata_34.img
Flashing : userdata_35.img
Flashing : userdata_36.img
Flashing : userdata_37.img
Flashing : userdata_38.img
Flashing : userdata_39.img
Flashing : userdata_40.img
Flashing : userdata_41.img
Flashing : userdata_42.img
Flashing : userdata_43.img
Flashing : userdata_44.img
Flashing : userdata_45.img
Flashing : userdata_46.img
Flashing : userdata_47.img
Flashing : userdata_48.img
Flashing : userdata_49.img
Flashing : userdata_50.img
Flashing : userdata_51.img
Flashing : userdata_52.img
Flashing : userdata_53.img
Flashing : userdata_54.img
Flashing : userdata_55.img
Flashing : userdata_56.img
Flashing : userdata_57.img
Flashing : userdata_58.img
Flashing : userdata_59.img
Flashing : userdata_60.img
Flashing : userdata_61.img
Flashing : userdata_62.img
Flashing : userdata_63.img
Flashing : userdata_64.img
Flashing : userdata_65.img
Flashing : userdata_66.img
Flashing : userdata_67.img
Flashing : userdata_68.img
Flashing : userdata_69.img
Flashing : userdata_70.img
Flashing : userdata_71.img
Flashing : userdata_72.img
Flashing : userdata_73.img
Flashing : userdata_74.img
Flashing : userdata_75.img
Flashing : userdata_76.img
Flashing : userdata_77.img
Flashing : userdata_78.img
Flashing : userdata_79.img
Flashing : userdata_80.img
Flashing : userdata_81.img
Flashing : userdata_82.img
Flashing : userdata_83.img
Flashing : userdata_84.img
Flashing : userdata_85.img
Flashing : userdata_86.img
Flashing : userdata_87.img
Flashing : userdata_88.img
Flashing : userdata_89.img
Flashing : userdata_90.img
Flashing : userdata_91.img
Flashing : userdata_92.img
Flashing : userdata_93.img
Flashing : userdata_94.img
Flashing : userdata_95.img
Flashing : userdata_96.img
Flashing : userdata_97.img
Flashing : userdata_98.img
Flashing : userdata_99.img
Flashing : userdata_100.img
Flashing : userdata_101.img
Flashing : userdata_102.img
Flashing : userdata_103.img
Flashing : userdata_104.img
Flashing : userdata_105.img
Flashing : gpt_main0.bin
Flashing : gpt_backup0.bin

Flash sequence completed!

Applying patches for storage # 0
Records : 26
Patch sequence completed!

Boot settings configured!

Flashing done!

Done!
Elapsed: 00:06:19

Reconnect Power/Cable!

Follow PAKFONES via social media and YouTube for more useful information about cellphone problem and solution.

Tags: , , , , ,

QMobile i8i Boot Key – Read Info – Tested Flash File

QMobile i8i Boot Key:

What is boot key? This hardware button that we are to connect phone in boot mode. We mostly using boot key to flash SPD phones. In some cases we need to press boot key also for MTK Android phones. Due to some changes in new SPD Android phones, boot key has been changed. I have noticed that QMobile i8i boot key has changed also which is now only Volume Up key. In previous SPD android phones The boot key was [Volume -] + [Volume +] key.

How to find boot key? In most of Android phone we have noticed that we need Vol Up + Vol Down key to connect phone for service purpose. But in some cases in different phones like SPD Featured phones this method not work. So now we need to find boot key for that phone, We will connect phone by pressing different keys one by one and when phones connected successfully we will see Serial port in device manager. But sometimes this method also fails then we need Boot Cable for SPD and MTK Phones.

QMobile i8i SPD Read Info With CM2SPD

To use read info for any SPD Android phone in Infinity CM2SPD, We need to select correct Boot Loader in settings tab, I have not seen any auto bootloader selection method for SPD Android phones. We can check mobile phones CPU inside with different ways.

  1. Using Power Supply Watch Video
  2. By Selecting different bootloader in Infinity CM2SPD Module
  3. Most effective Using Online Search (Learn from people’s experience)
  4. By opening phone

Settings Tab >> Select Boot >> Select Mode >> Service Tab >> Check/Info

Screenshot:

 

LOG:

Operation : Check/Read Info [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 13 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v1.0 
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FLASH : eMMC Flash , Structure : Ok!

Reading extended info ...

Model Name : I8i
Model Brand : QMobile
Model Device: I8i
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
CompileDate : 7/21/2017 11:50:35 AM
Project Ver : QMobile I8i_MP_21_07
Model Ext : QMobile I8i

ExtraInfo : HWInfo not exists, normal phone

Elapsed: 00:00:28

Reconnect Power/Cable!

QMobile i8i Read Flash Screenshot:

QMobile i8i Read Flash Log:

Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 13 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0 
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ...

Phone found! [ 13 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0 
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ...

Phone found! [ 13 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0 
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name : I8i
Model Brand : QMobile
Model Device: I8i
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : QMobile_I8i_MP_06_06
Model Ext : QMobile I8i

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ...

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W17.03.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 2431 MiB
Saved to : C:\Users\PAKFONES\Desktop\SP7731CEA_I8i_6.0_QMobile_I8i_MP_06_06_QMobile_I8i\
Done!

Elapsed: 00:17:17

Reconnect Power/Cable!

QMobile i8i Flash File

You can download QMobile i8i Flash File which is tested by us and This QMobile i8i flash file 100% working. No problem after flash. I have shared this flash due to there is bug in later version in QMobile i8i firmware. Just download QMobile i8i tested flash file for CM2.

  • Qmobile i8i restarting after opening box
  • QMobile i8i Hang and restart problem new phone

QMobile i8i Flashing Done:

Infinity SC Firmware Detected
FW Size : 2431 MiB
Load Ok!

File Info
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : QMobile
Device Model : I8i
Device CPU : sp7731cea
Device IntName : I8i
Device Version : 6.0
Device Compile : 6/21/2017 4:21:11 AM
Device Project : QMobile_I8i_MP_06_06
Device ExtInfo : QMobile I8i



Operation : Flash [ v1.24 ]

======= Flash
Files set for flashing : 
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 13 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0 
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

PMTManager : Load 0x19 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ... 
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ... 
Block erase Ok!
Write Data ... 
Write Data Ok!

Write FSImage : prodnv.img
Write Data ... 
Write Data Ok!

Write CodeData : sc7731C_CP0_modem.bin
Write Data ... 
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ... 
Write Data Ok!

Erase Block : RuntimeData
Erase block ... 
Block erase Ok!

Write CodeData : sc8830g_modem_CP2_WCN_Trunk_W17.03.5_Release.bin
Write Data ... 
Write Data Ok!

Erase Block : RuntimeData
Erase block ... 
Block erase Ok!

Write CodeData : logo_480x854.bin
Write Data ... 
Write Data Ok!

Write CodeData : fblogo_480x854.bin
Write Data ... 
Write Data Ok!

Write CodeData : boot.img
Write Data ... 
Write Data Ok!

Write FSImage : system.img
Write Data ... 
Write Data Ok!

Erase Block : PERSIST
Erase block ... 
Block erase Ok!

Write CodeData : sysinfo.img
Write Data ... 
Write Data Ok!

Write FSImage : cache.img
Write Data ... 
Write Data Ok!

Write CodeData : recovery.img
Write Data ... 
Write Data Ok!

Erase Block : MISC
Erase block ... 
Block erase Ok!

Write FSImage : userdata.img
Write Data ... 
Write Data Ok!



Elapsed: 00:04:09

Reconnect Power/Cable!

Difference in QMobile Firmware in phone and file version:

Tags: , , , , , , , , ,

QMobile M125 tested flash file

QMobile M125 tested flash file can be download from this post. You can flash this file using any Chinese Mobile Phone service device. I have used miracle box for flash and CM2 dongle for repair imei. because i failed with miracle box. You must have installed SPD drivers in your pc to work with this phone.

QMobile M125 Boot key

To work with most of Chinese mobile phone we need to press boot key to connect phone with service devices, Specially Spreadtrum (SPD) mobile phones. You can try by different keys. In this phone i have used special boot cable to connect phone in boot mode. You can also buy or make your own cable. by following instructions given in this post.

 

Screenshot

Flashing Log:

  1.Please Make sure install the driver
  2.The Phone may be required to read and write keys
  3.Pulled low may not, manually set.
  Definition Applied
  1. Power Off Phone , Remove Battery, Insert Battery Back
  2. Please Hold BootKey(UP and DOWN),Insert USB cable
  3. Use Miracle Boot Key In cases Boot key not Find
  4. Battery Should be Charged more then 50%
  Scanning USB Serial port...
  SU2Serial Port: COM34
  Connecting to Phone,Wait..
  Done.
  Infor: SPRD3
  Initialize boot9...
  CPU    type: 6531A
  Flash  type: NOR
  Flash    ID: 00EF0040(00160000)
  Flash Model: W25Q32BV
  Flash  Size: 0x400000(4.0M)
  reading,Wait...
  Read Completed.
  File save to: C:\Users\pakfo\Desktop\Qmobile M125 spd 6531\Backup\6531A_W25Q32BV.bin
  Definition Applied
  1. Power Off Phone , Remove Battery, Insert Battery Back
  2. Please Hold BootKey(UP and DOWN),Insert USB cable
  3. Use Miracle Boot Key In cases Boot key not Find
  4. Battery Should be Charged more then 50%
  Scanning USB Serial port...
  SU2Serial Port: COM34
  Connecting to Phone,Wait..
  Done.
  Infor: SPRD3
  Initialize boot9...
  CPU    type: 6531A
  Flash  type: NOR
  Flash    ID: 00EF0040(00160000)
  Flash Model: W25Q32BV
  Flash  Size: 0x400000(4.0M)
  writing,Wait...
  Write Completed.

IMEI repair  Log:

Operation : Repair Security [ v1.24 ]

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 34 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Process can take some time, please, wait
Init ok, send data
Write done!
Elapsed: 00:00:13

Reconnect Power/Cable!
Tags:

QMobile M2 Read Info

QMobile Read Info Done With Miracle Box.

I have made this post because i was stuck on witch cpu used in QMobile M2. So i found Qmobile M2 have Spreadtrum CPU in side. This phone have SPD6531A and it have NOR Flash GD27LQ32 in it. You can see read info log below.

Impotent: I have failed with boot key method. So i used special boot cable. You can also make your own cable.

How to connect phone?

  1. Press boot switch on cable and connect phone. Then install spd drivers.
  2. Open Miracle Box or any SPD6531A supported device.
  3. Select boot.
  4. Select Read Info Radio button.
  5. Tick USB Cable
  6. Press Start and then press boot switch on cable and connect it to phone.
  7. You will get all info in few seconds.
  8. Collected information from SPD phone can be found below.
 IMEI1 :353391081xxxxxx
 IMEI2 :35339108xxxxxx
 IMEI3 :35857001xxxxxxx
 IMEI4 :91057560xxxxxxx
 Unlock Code: 0000
 Unlock Code: 6806836
 Privacy Code: 0000

QMobile M2 Read info screenshot.

QMobile User Code Read Done With Miracle Box.

You can see read info and read flash log below. You can also download qmobile m2 flash file read by miracle box.This phone was in full working condition without any problem. After flashing this file you only need to reset phone. Phone password is 6806836.

 

 

Definition Applied
 1. Power Off Phone , Remove Battery, Insert Battery Back
 2. Please Hold BootKey(UP and DOWN),Insert USB cable
 3. Use Miracle Boot Key In cases Boot key not Find
 4. Battery Should be Charged more then 50%
 Scanning USB Serial port...
 count:=0_
 None SU2Serial Port.
 1.Please Make sure install the driver
 2.The Phone may be required to read and write keys
 3.Pulled low may not, manually set.
 Definition Applied
 1. Power Off Phone , Remove Battery, Insert Battery Back
 2. Please Hold BootKey(UP and DOWN),Insert USB cable
 3. Use Miracle Boot Key In cases Boot key not Find
 4. Battery Should be Charged more then 50%
 Scanning USB Serial port...
 SU2Serial Port: COM34
 Connecting to Phone,Wait..
 Done.
 Infor: SPRD3
 Initialize boot9...
 CPU type: 6531A
 Flash type: NOR
 Flash ID: 00C80060(00160000)
 Flash Model: GD27LQ32
 Flash Size: 0x400000(4.0M)
 Being analyzed,Wait...
 IMEI1 :353391081xxxxxx
 IMEI2 :35339108xxxxxxx
 IMEI3 :358570xxxxxxxxx
 IMEI4 :910575xxxxxxxxx
 Unlock Code: 0000
 Unlock Code: 6806836
 Privacy Code: 0000
>>If try all code and wrong, please read whole flash and then analyzed


 Definition Applied
 1. Power Off Phone , Remove Battery, Insert Battery Back
 2. Please Hold BootKey(UP and DOWN),Insert USB cable
 3. Use Miracle Boot Key In cases Boot key not Find
 4. Battery Should be Charged more then 50%
 Scanning USB Serial port...
 SU2Serial Port: COM34
 Connecting to Phone,Wait..
 Done.
 Infor: SPRD3
 Initialize boot9...
 CPU type: 6531A
 Flash type: NOR
 Flash ID: 00C80060(00160000)
 Flash Model: GD27LQ32
 Flash Size: 0x400000(4.0M)
 reading,Wait...
 Read Completed.
>>File save to: C:\Users\pakfo\Desktop\QMobile M2 6531A_GD27LQ32.bin

Note: Do it at your own risk. We are not responsible for any damage. This information we have posted only for educational purpose.

Tags: , , , ,

QMobile V2 Tested Flash File

QMobile V2 Tested Flash File read by infinity cm2 v1.32. Qmobile Noir V2 firmware is tested and 100% working for me. If you have not CM2 dongle you also flash this firmware with sp flash tool. Just download MT6582__QMobile__QMobile V2__QMobile V2__4.4.2__ALPS.KK1.MP1.V2.10_[pakfones.com].zip.001 and 002 files. Extract these file using 7zip. Then rename .zipp to .zip then extract again and flash using infinity cm2 MTK module. if you have not cm2 dongle then follow the qmobile noir v2 flash screenshots.

QMobile Noir V2 Tested Firmware Download Links.

[ Sorry Link Removed Due To Bug In Firmware Phone Bricked After Writing ]

  • MT6582__QMobile__QMobile V2__QMobile V2__4.4.2__ALPS.KK1.MP1.V2.10_[pakfones.com].zip.001
  • MT6582__QMobile__QMobile V2__QMobile V2__4.4.2__ALPS.KK1.MP1.V2.10_[pakfones.com].zip.002

File Size: Part .001= 700mb and Part .002= 561mb

How to Flash MTK Smart Phones With SP Flash Tool

Tags: , , , , , ,

QMobile Z14 Dead Solution

In this post i am going to share QMobile Z14 Dead Solution. This method is tested and working. But due to very huge size of this file we have spent much time and internet data to upload this file. So this file is paid. Not for free if you are searching for free you should read your own backup from working phone with miracle box.

Reason: Why QMobile Dead After Flashing Backup?

Every phone have special encrypted security inside. QMobile Z14 also have encrypted security. QMobile Z14 is based on MT6755 and its newest MTK 6755 CPU. Infinity CM2 or other Chinese software service devices have not decryption for QMobile Z14 MT6755 based phone.

Story: We get phone with screen lock. and try to read screen lock but failed, We try to format after reading full factory firmware backup with CM2MTK, We got encryption error after format. And then QMobile z14 totally dead after flashing its own backup. We also have shared qmobile z14 firmware.We not recommend you to use This firmware use it at your own risk. We need only this Qmobile z14 firmware when we facing error in miracle box flashing bin file.

 

How To Repair QMobile Z14 Dead After Flashing Factory Firmware read by CM2.

To repair QMobile z14 dead by flashing factory firmware read by any Chinese service software device. Like Miracle Box, CM2 Dongle, Volcano Box and some others. You need some experience of flashing mtk phone with these devices. and you must have cm2 and miracle box to recover devices. If you not have these devices you can continue at your own risk. we can give you help only if you have these two devices. So let’s start..

  • Download QMobile Z14 Firmware bin file read by miracle box links can be found below.
  • Download and install MTK usb drivers.
  • Download Latest TeamViewer Software and Give us ID and Password to unlock firmware.
  • Open Miracle Box
  • Select Boot8
  • Select Bin firmware give below file.
  • Tick USB cable and press “Start”
  • Connect mobile to PC via Micro USB cable.
  • Write NV file give by zulqar.
  • Repair you QMobile Z14 IMEI with original. This can be done with CM2.

QMobile Z14 Bin Flash File Password Protect:

Firmware file is 29.xx GB so you must have more then 40GB space where you are going to extract files.

  1. QMobile Z14 BIN Firmware MTK6755_1612041311.zip.001
  2. QMobile Z14 BIN Firmware MTK6755_1612041311.zip.002
  3. QMobile Z14 BIN Firmware MTK6755_1612041311.zip.003
  4. QMobile Z14 BIN Firmware MTK6755_1612041311.zip.004
  5. QMobile Z14 BIN Firmware MTK6755_1612041311.zip.005

QMobile Z14 NV File: QMobile Z14 NV File CM2.rar

File price 500 PKR or 5 USD

Please note this file is not for free. We just shared info how to recover dead Qmobile z14 after flash. So if you want Qmobile Z14 Full backup 32GB visit contact-us page or contact via Whatsapp +92-300-4537-079.

 

QMobile Z14 Bin file flashing log:

Miracle Box Version 2.40
Release: 11th November 2016
System Info:
MT65xx ANDROID EMMC File:
Definition Applied
1. Power Off Phone , Remove Battery, Insert Battery Back
2. Insert USB cable. In some cases Required Hold BootKey
3. Use Miracle Boot Key In cases Boot key not Find
4. Battery Should be Charged more then 50%
Waiting for USB Port...
The File Information:
N/A
Set MediaTek PreLoader USB VCOM Port (COM63)
Please Hold "ON" to connect with the phone...
Connected to Phone.
CPU: MT6755 SW:0001 Ver: CB00
Downloading Boot8 ...
EMMC Size: 0x0747C00000
Flash Type: EMMC
INT/EXT RAM  Size: 0x40000/0x80000000
Writing(Nand/eMMC)...
Writing preloader
Writing recovery
Writing md1img
Writing md1dsp
Writing md1arm7
Writing md3img
Writing lk
Writing lk2
Writing boot
Writing logo
Writing tee1
Writing tee2
Writing secro
Writing system
Writing cache
Writing userdata
Write Done.
Total time: 68 mins 43 s

 

 

Tags: , , , , , , ,

QMobile S1 Firmware

How to Flash QMobile S1  Free With SP Flash Tool?

  • First download firmware for you cellphone and extract it using any unzip utility.
  • Install required MTK USB drivers.
  • Open SP Flash Tool v5.1612 available in firmware package or download from given link.
  • Press Scatter-loading button and go to firmware folder select MT65xx_Android_scatter.txt
  • Press Download button and wait let sp flash tool to test firmware files that are going to be flashed when finish file checking immediately connect powered off  mobile phone to USB cable.
  • Let Sp Flash Tool finish the job it will take few minutes.
  • Download OK message will be appear on screen with big green [O]
  • Disconnect phone from USB cable after appearing of Download OK message with big green [O]
  • Power on your mobile phone and wait few minutes to complete boot process first time.
  • Then configure phone with your required setting and done!

Please visit How to Flash MTK Smart Phones With SP Flash Tool for video tutorial and screenshots flashing with sp flash tool.

 

QMobile S1 Firmware:

[button link=”https://drive.google.com/open?id=0B6zvh2EoixSncGMxeUdTbUZ2U0U” icon=”Select a Icon” side=”left” type_color=”button-background” target=”” color=”b70900″ textcolor=”ffffff”]QMobile S1 Firmware Free Download[/button]

 

QMobile S1 Firmware Flashing Done With CM2 Dongle:

Chinese Miracle II [MTK module] v 1.56


Scatter Load Ok , BaseBand : MT6582 , Project : s5222 , Storage : EMMC
 Files found : 11 , Set to Flash : 10
 Ready to Flash!

Operation : Flash [ v1.56 ]

======= Flash
 1. Power Off Phone , Remove battery , Insert back
 2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
 Phone found! [ 19 ]
 Sync...
 Inital Boot Ok!
 BB_CPU_PID : 6582
 BB_CPU_NME : [MediaTek] MT6582_S00
 BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
 Processing BROM stage
 Settings for BROM configured!
 SecCfgVal : 0x00000000
 BromVer : 0x00FF
 BLVersion : 0x0001
 PreLoader : Active [ Boot with PL ]
 BootLdrSS : NORMAL with PRELOADER
 Processing DA stage
 DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
 Sending and initialize DA ...
 Running DA ver.4.2 on BBID : 0x87
 NAND Flash : NOT INSTALLED
 eMMC Flash : 90014A4838473165050733B7991492C9
 Initialize Memory ...
 DRAM already initialized by Preloader
 DAgent sent , init HW now
 eMMC FlashIC initialized
 [eMMC] : FLASH_VEN : 0x90 , OEM : 014A
 [eMMC] : FLASH_INF : [HYNIX] , e1G8
 [eMMC] : FLASH_CID : 90014A4838473165050733B7991492C9
 [eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
 [eMMC] : FLASH_LEN : 0x00000001D2000000
 [eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
 DEV RID : 0x4B87B7682CA66847157DA714184590A7
 INT RAM : 0x00020000
 EXT RAM : 0x40000000 [1 GiB]
 BOOT TYPE : EMMC_FLASH_BOOT
 SOC VERIFY : C1
 Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : s5222 , Storage : EMMC
 Setting : Flash Pre-Erase (Safe) : Enabled
 Setting : AFF verify : Enabled
 Setting : HW verify : Enabled

BL : Check HW compatibility
 BL : BBID supported by BootLoader!
 BL : Check eMMC compatibility
 BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3498 mV
 BL : [WARNING] : BatteryLevel LOW!!!

BL : Flash Pre-Erase
 Total blocks to Erase : 2
 Erase : 0x0000000000C00000-0x0000000000100000
 Erase : 0x0000000002900000-0x00000001CEE00000
 Flash Pre-Erase Done, time used : 00:00:02

SecCfg Passed , 1799
 BMT remark not need. Will skip
 Sending Preloader ...
 Use : preloader_s5222.bin
 Preloader Sent , Init passed
 SecCfg Passed , 1799
 PartCount : 0012
 Update PMT by user request
 Repartition Done!
 Use FLN Mode

Processing : Flash Write
 Flash now : MBR
 Image Flash Ok
 Flash now : EBR1
 Image Flash Ok
 Flash now : UBOOT
 Image Flash Ok
 Flash now : BOOTIMG
 Image Flash Ok
 Flash now : RECOVERY
 Image Flash Ok
 Flash now : SEC_RO
 Image Flash Ok
 Flash now : LOGO
 Image Flash Ok
 Flash now : ANDROID
 Image Flash Ok
 Flash now : CACHE
 Image Flash Ok
 Flash now : USRDATA
 Image Flash Ok
 Flash Write Done, time used : 00:03:31

Processing : Verify
 Verify Passed : MBR
 Verify Passed : EBR1
 Verify Passed : UBOOT
 Verify Passed : BOOTIMG
 Verify Passed : RECOVERY
 Verify Passed : SEC_RO
 Verify Passed : LOGO
 Verify Passed : ANDROID
 Verify Passed : CACHE
 Verify Passed : USRDATA
 Data Verify Done, time used : 00:01:55

Update Mirror PMT
 Update Done!

Update RomInfo done

Done!
 Elapsed: 00:05:42
 Reconnect Power/Cable!
Tags: , , , , , ,

QMobile L10 Flash File

QMobile L10 Flash file free download. In this post will try to post all available QMobile L10 firmware files. I will also try to post how to flash QMobile LINQ L10 or how to upgrade QMobile l10 with sd card. but this time i have not screenshots or video for this phone i will try to add more information about QMobile L10 flashing or upgrading when i get phone to repair.

 

 

QMobile LINQ L10 Fastboot Firmware link Google Drive secure online storage

QMobile LINQ L10 SD Card Upgrade Firmware link Google Drive secure online storage

 

Please Note: Read phone first before flash or do anything. We are not responsible for any damage or illegal use of information given by us. We are posting to help people. Its up to you that you are using this information for positive work or illegal. If you want to share this file your are free to share [Only our website link sharing allowed] We don’t allow direct file links sharing.

Subscribe Via Email: If you think this website helped you to solve your problem. And in future you want to get email notification on every useful post from this website. Please write you email in Subscribe Via Email and press Subscribe and conform your email. In your email inbox. Now you will get email notifications via your email inbox.

Suggestion: If your problem not solved by given solution you can write in comments we will try to fix as soon as we can. If you have not required software or devices don’t worry we will fix your phone online or you can visit us or send us to our Service Lab Address via any Currier service. To fix the problem.

 

Tags: , , , ,

QMobile z14 firmware

Qmobile z14 firmware file tested and read from fully working phone. this file is read by infinity cm2. Qmobile z14 firmware file can be flash with sp flash tool also if you have not infinity cm2. There is no risk to flash this QMobile z14 flash file. But we strongly recommended that you take a full firmware backup before flashing any phone. Please read all post till end if you have not any experience of smart phone flashing before. We hope you will learn from this post and can repair your own cellphone.

QMobile z14 firmware

How to flash QMobile Z14 Factory Firmware:

  • First download firmware for you cellphone and extract it using any unzip utility.
  • Install required MTK USB Drivers.
  • Open SP Flash Tool available in firmware package or download from given link.
  • Press Scatter-loading button and go to firmware folder select MT67xx_Android_scatter.txt
  • Press Download button and wait let sp flash tool to test firmware files that are going to be flashed when finish file checking immediately connect powered off  mobile phone to USB cable.
  • Let Sp Flash Tool finish the job it will take few minutes.
  • Download OK message will be appear on screen with big green [O]
  • Disconnect phone from USB cable after appearing of Download OK message with big green [O]
  • Power on your mobile phone and wait few minutes to complete boot process first time.
  • Then configure phone with your required setting and done!

For detailed flashing tutorial with screeshots and video please visit How to Flash MTK Smart Phones With SP Flash Tool. If you still have question please leave in comments.

 

Please Note: Read phone first before flash or do anything. We are not responsible for any damage or illegal use of information given by us. We are posting to help people. Its up to you that you are using this information for positive work or illegal.

Subscribe Via Email: If you think this website helped you to solve your problem. And in future you want to get email notification on every useful post from this website. Please write you email in Subscribe Via Email and press Subscribe and conform your email. In your email inbox. Now you will get email notifications via your email inbox.

Suggestion: If your problem not solved by given solution you can write in comments we will try to fix as soon as we can. If you have not required software or devices don’t worry we will fix your phone online or you can visit us or send us to our Service Lab Address via any Currier service. To fix the problem.

 

 

Tags: , , , , , , , ,