How to fix *#06# not working on Samsung

Here is how to fix Samsung s6 edge SM-G925F not accepting some codes like *#06#, *#0808# and some others. this post will help you to fix Samsung secret code not working on your Samsung. This post is about How to fix *#06# not working on Samsung S6 Edge, but you can use this method for all Samsung witch have same problem.

Most of people facing problem in their Samsung Phones Like:

  • how to fix Samsung s6 edge *#06# not working?
  • How to fix *#0*# code not working on Samsung?
  • Secret code not working on Samsung S7 Edge.
  • How to upgrade Samsung S6 Edge to Marshmallow 6.0.1?
  • How to flash Samsung S6Edge 6.0.1 firmware?
  • How to skip some files from Samsung firmware?
  • Samsung dialer codes not working

So these all related to firmware so you can fix these errors via changing firmware with correct version which your cellphone belongs to. In other words you can fix Samsung dialer codes not working by flashing your cellphone with correct one. Please check your cellphone comes from which country and then search firmware for same country and carrier.

But in some cases people facing problem during changing firmware, like flashing error with specific file name flashing failed sboot.img, boot.img, recovery.img, system.img,ext4.img, cache.img, cm.img,modem.img you can skip flashing any file from Samsung firmware. please read detail below i have done this during Samsung S6 Edge upgrade.

What things are needed to upgrade s6 edge firmware?

How to delete or skip some files from Samsung firmware?  because in this s6 edge case hidden.img needed to delete from g925F firmware. Rename firmware file .md5 to .tar
G925FXXU3DPC2_G925FOJV3DPB4_G925FXXU3DPBT_HOME.tar.md5
G925FXXU3DPC2_G925FOJV3DPB4_G925FXXU3DPBT_HOME.tar 
Now open firmware file with Alzip and select Hidden.img file right click on it and press delete this will take few minutes to re compress firmware after few minutes this will finish the job now close Alzip and open Odin or Z3X or any other that you already using to flash Samsung firmware.
Detailed post about How to flash Samsung using Odin with video
Select firmware and press Start this will take few minutes to finish this job. you can disconnect usb cable after flashing finished. do hard reset Samsung s6 edge after flash. you have done now phone should be in working good after this. flashing screenshot and and log can be found below.
Note: This is tested and working without any error but This web site not responsible for any damage. by you mistake. if you get any problem you can contact us via contact page can be found in bottom of the main page of this site. for help. will will fix your phone over team viewer. 

FLASH INSTRUCTIONS:
1. Choose correct flash file(s).
2. If you have PIT file chosen, then you must check ‘Repartition’ option.
3. Check flashing options if needed (Repartition, EFS clear, Boot update).
4. Power on phone in download mode (turn off phone, press vol.down + home + power).
5. Connect phone to PC with USB cable, install drivers if needed.
6. Press ‘Flash’ button.

Operation: Flash
 Selected model: SM-G925F
 Software version: 25.0

File analysis... OK
 Total file size: 0xE3772BA0 (3639 Mb)
 Searching USB Flash Interface... detected COM30
 Setup connection... OK
 Reading PIT from phone... OK
 Sending sboot.bin... OK
 Sending cm.bin... OK
 Sending boot.img... OK
 Sending recovery.img... OK
 Sending system.img... OK
 Sending modem.bin... OK
 Sending cache.img... OK
 Flashing done (time - 00:04:28)
 Done with Samsung Tool PRO v.25.0

Leave a Comment